Accessories for moisture meters

Of course, we can supply the spare parts for all instruments produced by LogicaH&S, from the single screw to the most upgraded electronic board.

 

As for boards, we can also supply customers with our technical assistance which is able to repair (and not only to replace!) electronic boards: in this way we can guarantee very low assistance costs (often assistance is free!). In case of emergency, we can supply, in accordance with customers, a replacing board (a new or restored one) while the customer sends us back the damaged one, to assure a very short interruption of machine working in all over the world.

nuovi_accessori_logica-46.png
Relative humidity / temperature sensor for instruments
LG43 Series

The C001553 sensor allows you to use your LG43 meter for measuring ambient humidity. In addition to the relative humidity and temperature values, the instrument also calculates and displays the wood balance humidity (EMC).

The accurate shielding of the sensor also makes it ideal for use inside the drying oven.

nuovi_accessori_logica-35.png
Relative humidity / temperature sensor for instruments
MoistXXXX series

The C002836 sensor allows you to use your MoisTest or MoisTrue meter for measuring the ambient humidity.

In addition to the relative humidity and temperature values, the instrument also calculates and displays the wood balance humidity (EMC). The accurate shielding of the sensor also makes it ideal for use inside the drying oven.

nuovi_accessori_logica-40.png
Relative humidity probe for concrete floors

This accessory for the LG43 instrument is suitable for use with the items described above, to measure the relative humidity in concrete floors in compliance with the ASTM F2170 standard.

The probe (Ø 10mm) inserted in the aluminum seat ensures an excellent seal guaranteeing reliable measurements.

Code C002103

nuovi_accessori_logica-42.png
Aluminum seat for holes in concrete floors

These elements are provided with a plug and a sliding gasket (to adapt perfectly to the depth of the hole) and have two deformable gaskets to seal the holes in which the humidity detection probes will subsequently be positioned.

The diameter of the hole required for their insertion is 14 mm.

C002100 aluminum seat L = 50mm
C002101 aluminum seat L = 100mm

nuovi_accessori_logica-37.png
RH/T/EMC sensor for LG51 / LG52

It is a resistance meter accessory for estimating the humidity of sawdust or wood chips, particularly suitable for humidity lower than 20%.

 

Connected to compatible meters, it must be inserted deep into the material to be measured.

CODE: C002989 - INOX probe - length 30cm - Ø8mm

nuovi_accessori_logica-48.png
SPF probe

It is a resistance meter accessory for estimating the humidity of sawdust or wood chips, particularly suitable for humidity greater than 15%.

Connected in place of the normal electrode holder, it must be inserted deep into the material to be measured, suitably compacted.

CODE: C001909 - SPF AISI304 probe - length 60cm - Ø12mm

nuovi_accessori_logica-18.png
Test Box for moisture
meters calibration

C001578 Test Box for checking resistance meter calibration
(11.5% 25 ° C Group 3)

C000910 Test Box for checking calibration of resistance meters (18.5% 25 ° C Group 3)

C000911 Test Box for checking calibration of resistance meters (32.5% 25 ° C Group 3)

nuovi_accessori_logica-58.png
TESTBOX FOR moistestxx
contact TYPE meters

Test Box for checking the calibration of contact gauges for the Moistest series.

 

Compatible with MT10, MT20 and MT30

 

C002951

nuovi_accessori_logica-34.png
Conductive rubber electrodes for surface measurements

Pair of AISI303 stainless steel electrodes fitted with conductive rubber for surface measurements.

These items do not damage the measured material in any way.

They are used with the Probe, simply by screwing them onto the instrument instead of nails.

CODE: C001432

nuovi_accessori_logica-52.png
insulated electrodes for
pin type meters

Usable with our driving tools, they are made of treated steel.
These electrodes have an extremely sharp tip that allows easy measurements even in depth.

INSULATED VERSION: The insulated stem allows the measurement of the correct humidity of the wood in depth even in the presence of a moist surface layer (e.g. frost)


Two different lengths are available in the catalog and can be used with the electrode holder hammer or with the probe.

Code C002679 - ASSORTED SET 20 electrodes (10 x 25mm, 10x40mm)
Code C001945 - SET 25 (20 25mm electrodes)
Code C001946 - SET 40 (20 electrodes of 40mm)

nuovi_accessori_logica-57.png
non-insulated electrodes for pin type meters

Usable with our driving tools, they are made of treated steel.
These electrodes have an extremely sharp tip that allows easy measurements even in depth.

 

NOT INSULATED VERSION: They can be used in place of the insulated ones in all cases where there is not a more humid layer on the surface, guaranteeing a saving on the purchase price and greater strength.

 

Two different lengths are available in the catalog and can be used with the electrode holder hammer or with the probe.

 

Code C002345 - ASSORTED SET 20 electrodes (10 x 25mm, 10x40mm)
Code C002346 - SET 25 (20 25mm electrodes)
Code C002347 - SET 40 (20 electrodes of 40mm)

nuovi_accessori_logica-20.png
Electrodes with perforation
for surface measurements

Turned steel electrodes with very short (0.5mm) and sharp tip, suitable for measurements on thin materials (veneers, paper, leather) or for surface measurements.

The short and sharp tip allows non-intrusive measurements in the materials, leaving almost imperceptible marks.

Particularly suitable for use on a probe, they can also be installed on the electrode holder hammer.

CODE: C000548

nuovi_accessori_logica-31.png
Connection cable
for hammer and feeler

Connection cable made with highly insulated cables and connectors, allows you to connect feeler or hammer to the LG43 instrument ensuring reliable measurements.

CODE: C000102

nuovi_accessori_logica-54.png
feeler pin for
surface readings

Accessory for drive-in measuring device mod. LG43, consisting of a practical high insulation handle and a series of turned steel electrodes with a thin tip and a penetration depth of 0.5mm. Useful for surface measurements on veneers or non-wood materials. It can also accommodate standard 40 or 60 mm electrodes.

 

CODE: C000095

nuovi_accessori_logica-55.png
Electrode hammer
for deep readings

Accessory for drive-in measuring device mod. LG43, consisting of a powder-coated metal part with striking mass from a head in highly insulated plastic material.

 

The striking mass allows an easy insertion (and extraction) of the electrodes in the material to be measured.

 

CODE: C001626 Weight about 1.5 kg

nuovi_accessori_logica-56.png
spare hammer head

If the plastic section of the hammer C001626 is damaged, only the damaged part can be replaced.

This particular must necessarily be made of highly insulated plastic material, therefore it is more fragile than the remaining parts of the accessory.

 

However, it is possible to ensure a very long life by simply avoiding tightening the electrode locking nuts too hard and making guide holes for measurements on particularly hard materials or at very great depths.

 

CODE: C000584